Does Your Bow Sight Need Third-Axis Adjustability?

Does Your Bow Sight Need Third-Axis Adjustability?

If you're a bowhunter and you've done some reading up, you've probably heard the phrase "third-axis adjustment." It's a term for one of several axes on which a bow sight can be rotated and adjusted. Bow sights should be plumb with the bow so that the shooter can be better be assured that the bow is not canted, because inadvertently canting the bow can ruin accuracy at long range. But before getting to the third axis, we should briefly discuss the first and second.

First Axis

To understand what is called the first axis, picture an imaginary line running through the bow sight from left to right that would allow the bottom of the sight to swing toward or away from the archer like a mud flap on a truck. This axis should be perfectly perpendicular with the bow's riser before the next two axes can be properly leveled. It can be aligned using a bow square, a regular carpenter's square or even a door frame that you know to be plumb. Or, of course, you can take your bow into an archery pro shop and let them do it – for a small fee.

Second Axis

For the second axis, imagine a line running from the target, through the bow sight, to the archer's eye. All of the sight pins should line up vertically on this plane. (In other words, they should form a vertical line that's parallel to the bow's riser.) It's important to get this second axis perfectly plumb with the bow (and level with the ground) so that the archer can use the sight's bubble level while shooting and know that if it is level, then the pins are in line, and so the arrow will strike on the same vertical plane no matter the sight pin chosen. It's very important for precision shooting at longer distances.

Third Axis

The third axis, however, is not important for the average bowhunter who doesn't shoot much past 40 yards and/or at extreme upward and downward angles. Sitting 15 feet up in a treestand and shooting something at 35 yards doesn't constitute an extreme angle or need for precision third-axis adjustment. It's more regarded by western hunters who may shoot at targets 60 yards distant and 40 yards down (or up) a cliff face. Extreme target archery tournaments, like the Total Archery Challenge, make a point of setting up these difficult shots. So, if you're not one of these guys who must shoot at such crazy angles, you probably shouldn't fret over your third-axis adjustment. But if you are an extreme target shooter, a mountain hunter – or just a perfectionist – you can enhance your long-range accuracy by making sure it's perfectly adjusted. It's complicated to explain by mere words, but here goes.

Adjusting bow sight

Imagine a plane running vertically down though the bow sight that would allow the bow sight to rotate like a revolving door. If that door (the sight) is slightly pulled slightly open or pushed back (in relation to the bow's riser) and then angled up or down (as if taking an extreme uphill or downhill shot), the relationship between the bow sight and the ground can change, causing it to become out of level with the ground, and therefore causing your arrow to be off.

But it's not as simple as using a square to make sure the sight's third axis is plumb with the riser while it's in a vise; third axis is best evaluated while at full draw. Torque placed on the bow by the shooter's hand and the cable guard can affect the third axis. While there are specialized tools designed to check the third axis, you can check it at home, if you know what you are doing. To check, draw a perfectly vertical scribe line at the bottom of a wall. Place a bubble level on the bow. Then, while facing the wall, draw the bow, and while aiming it down at a 45-degree angle, make sure the bow is level by viewing the bubble level. Next, make sure the sight pins perfectly line up on the scribe line. If they do not, you'll need to make adjustments to the third axis.

Some newer and more expensive bow sights have third-axis adjustments, but most hunting sights do not. For these, a small shim such as a strip of duct tape or a length of business card placed between the sight's mounting bracket and the riser can often tilt the sight's third axis enough to do the trick. But if you are serious about perfection, you are probably best served by buying a sight with an integral third axis hinge that can be easily adjusted.

Fact is, most hunters – especially eastern whitetail hunters – can hunt their whole lives and never worry a third-axis adjustment. But if you're a bowhunter who might shoot a mule deer from a cliff face or plan to bowhunt sheep – or maybe you're just an archery geek – be sure to check your third axis.

Recommended for You

North America

The Best Units for Hunting Elk, Mule Deer & Antelope

Chuck Smock

These are the must-apply units for trophy elk, mule deer, and antelope in the West.


Booth Babes from the 2012 SHOT Show

PH Online Editors - January 18, 2012

Companies in the outdoor industry know how to get our attention. We know, it might seem cheap,...

Other Game

Today's Updated Turkey Hunting Gear

Joe Arterburn

The most modern ammo and gear increase the odds of bagging a tricky tom this spring.

See More Recommendations

Popular Videos

2018 Petersen's Hunting Episode 14: Swamp Bulls

With his Mozambique forest bull in the salt, Craig Boddington sets his sights on the Marromeu grasslands in pursuit of a swamp buffalo.

2018 Petersen's Hunting Episode 9: Aloha Axis Deer

Host Mike Schoby joins his buddies Jon Dubin and Jeff Johnston on the island of Lanai for a deer hunt Hawaiian style!

2018 Petersen's Hunting Episode 10: Snowbound Chamois

Host Brittany Boddington gets more than she bargained for on what turned out to be a grueling, snowbound and extremely physical hunt for chamois in Romania's Carpathian mountains.

See more Popular Videos

Trending Stories

North America

5 Great Last-Minute Public-land Hunts

Joseph von Benedikt - October 16, 2017

Didn't draw? Here are five great places you can still make a 2017 mule deer hunt. According to...


America's Top 10 Big Game Cartridges

Joseph von Benedikt - September 19, 2016

These rounds have proven themselves most worthy in the field.


17 Dream Jobs in the Outdoor Industry

Kali Parmley - June 14, 2016

Combining a career with your passions is a goal that is strived for, but not often achieved....

See More Stories

More Bowhunting


Top Field-Tested Broadheads for Fall 2018

Jeff Johnston - November 01, 2018

Looking for a new broadhead this fall? Check out our top picks for the best this year has to...


Head-to-Head Review: Top Crossbows of 2014

PH Online Editors - July 10, 2014

As we began our annual x-bow test, it was clear that there would be a certain level of...


Horizontal Thinking: Best Crossbows for 2018

PH Online Editors - January 19, 2018

Mission Crossbows Here is a brief overview of some of the hot new crossbows for

See More Bowhunting

GET THE MAGAZINE Subscribe & Save.

Temporary Price Reduction.


Give a Gift   |   Subscriber Services


GET THE NEWSLETTER Join the List and Never Miss a Thing.